General Requirements For Wiring Methods And Materials Practice Test

These questions are part of the practice quiz. Start practicing

• What is permitted in lieu of a box or terminal when conductors emerge from a raceway and enter equipment?
• A ______ is not considered a plenum space.
• What does NEC require regarding the identification of grounded conductors?
• For what voltage is the lighting system for pool, spa, and fountain limited in a nonmetallic raceway?
• The space above a hung ceiling used for environmental air-handling purposes is an example of ______.
• Where type NM cable passes through openings in metal members, it shall be protected by ______ bushing or ______ grommets.
• What is the minimum cover depth for direct burial conductors?
• In relation to listing, what must a low-voltage lighting system be to allow for different installation instructions?
• What is the function of a circuit breaker in an electrical system?
• Can a single grounding conductor serve multiple circuits according to NEC?
• What is the purpose of derating when more than three conductors are used in a raceway?
• Which document must be consulted for special installation requirements for specific appliances?
• Wiring methods installed behind access panels must be _____ according to applicable articles.
• To protect cables or tubing likely to be penetrated, a steel sleeve or plate must be at least ________ in. thick.
• The independent support wires for supporting electrical wiring methods in a fire-rated ceiling assembly shall be distinguishable by which of the following?
• To prevent heating surrounding ferrous metal in raceways, which type of conductor should be grouped together?
• What does NEC require regarding raceways exposed to physical damage?
• What is the maximum vertical distance for cables or raceways to the top of metal-corrugated decking?
• What is the common minimum size of a grounding electrode?
• Where raceways contain insulated circuit conductors of which AWG size and larger, must they be protected from abrasion during and after installation?
• Independent support wires used for the support of electrical raceways and cables within fire-rated assemblies shall be distinguishable from the suspended-ceiling framing support wires. Is this statement true or false?
• What is the role of GFCIs in certain installations?
• Wiring methods and equipment installed behind suspended-ceiling panels shall be arranged to allow access to the electrical equipment.
• What is the minimum distance that raceways or enclosures must protect direct-buried conductors when emerging from grade?
• Which section of the NEC covers the installation of conductors in a raceway?
• Which of the following is NOT a recommended practice for circuit installations?
• In which conditions is the use of conduit unnecessary?
• Conductors installed in nonmetallic raceways run underground are permitted to be arranged as _______, installations.
• What is an important safety feature required for electrical boxes?
• Electrical equipment with ______ and low smoke and heat release properties can be installed within air-handling space (plenum).
• Wiring methods and cabling systems permitted in plenums shall be installed in ducts specifically fabricated for environmental air-handling purposes ______.
• Expansion fittings must be provided in raceways to compensate for which of the following?
• What does Article 368 of the NEC cover?
• What is the primary purpose of the NEC Code Book?
• Why is the NEC's "general requirements" essential for electricians?
• Are circuits supplying only lighting required to be on separate branches?
• Which article of the NEC contains the requirements for branch circuits?
• Are boxes or conduit bodies necessary for splices and taps in direct-burial conductors if a splicing device is used?
• Is a box or conduit body required for conductors in hand-hole enclosures except when connected to electrical equipment?
• In what situations is underground wiring permitted according to NEC?
• Cable wiring methods shall not be used as a means of support for ________.
• Why must electrical wiring in ducts be handled carefully?
• Raceways, cable assemblies, boxes, cabinets, and fittings shall be securely fastened in place. Is this statement true or false?
• ________ shall be permitted to support the wiring methods and equipment in other spaces used for environmental air (plenum).
• Raceways, cable trays, cablebus, auxiliary gutters, cable armor, boxes, cable sheathing, cabinets, elbows, couplings, fittings, supports, and support hardware shall be of materials suitable for ______.
• When splices are made with a qualifying splicing device, are boxes or conduit bodies needed?
• Which of the following must be provided with supplementary corrosion protection?
• Raceways can be used as a means of support for Class 2 circuit conductors or cables that connect to the same equipment. Is this statement true or false?
• Where corrosion protection is necessary for ferrous metal equipment and the conduit is threaded in the field, the threads shall be coated with a (n) __________ electrically conductive, corrosion resistant compound.
• Which article in the NEC predominantly addresses general wiring methods?
• What does the term "ampacity" refer to?
• When must GFCI protection be provided according to NEC?
• When can non-metallic sheath cable be installed without additional protection?
• The number and size of conductors permitted in a raceway is limited to ensure what?
• When portions of a cable raceway are subjected to different temperatures, what should be done to prevent air circulation?
• Do the rules for spacing from decking apply equally to rigid metal conduit and intermediate metal conduit when installed under metal-corrugated sheet roof decking?
• For a vertical run of 4/0 AWG copper, what is the maximum recommended support interval?
• Prewired raceway assemblies may only be used under what condition?
• "S" loops in equipment direct burial ______ to raceway transitions, expansion fittings in raceway risers to fixed equipment, and generally, the provision of flexible connections to equipment subject to settlement or frost heaves are recognized by the NEC.
• What is the minimum number of support methods required for each conductor in a vertical raceway that exceeds given height values?
• An exposed wiring system in indoor wet locations should be mounted with at least a ______ between the mounting surface and the electrical equipment.
• Protection against nails or screws for cables in wood notches requires a steel plate at least _______ in. thick.
• What must backfill used for underground wiring not damage?
• Is it permissible to use aluminum conductors instead of copper conductors?
• For which type of occupancy does NEC require emergency circuits?
• Ferrous metal raceways and related hardware can be installed in environments subject to severe corrosive influences only when they are ______ approved for the condition.
• When installed through bored holes, cables should maintain how much distance from the edge of a wood member?
• What term is defined as the area between the top of direct-burial cable and the top surface of the finished grade?
• For locations not specifically identified in Table 300.5, what is the designation of a low voltage lighting system that allows for a lesser cover depth?
• What is the purpose of short sections of raceways in electrical installations?
• What is the permitted cover depth in inches for pool, spa, and fountain lighting installed in a nonmetallic raceway under certain conditions?
• What is the primary code that governs general requirements for wiring methods and materials in the United States?
• When exposed to sunlight, nonmetallic raceways and components shall be ______.
• What is required for openings around electrical penetrations in fire-resistant rated structures?
• Which of the following is NOT allowed in spaces used for environmental air?
• Nonmetallic wiring methods exposed to chemicals must be inherently resistant based on their being ______ for the specific chemical reagent.
• What is the maximum allowable voltage drop for feeder conductors according to NEC?
• What is the function of a grounding electrode?
• Which of the following should not have wiring installed within ducts?
• What is the minimum required height for overhead service conductors above ground?
• What type of fitting must be used where a raceway crosses a structural joint intended for expansions, contraction or deflection in buildings?
• What is the minimum cover requirement for type UF cable supplying power to a 120V, 15A GFCI-protected circuit outdoors?
• For a wiring system in wet locations, what is required for mounting?
• When are recess fixtures considered dangerous according to the NEC?
• Is it permissible for metal raceways to be installed in concealed locations under metal-corrugated roofing?
• What factor must be considered for ampacity adjustments?
• What method can be used to enhance fire safety in electrical installations?
• What minimum length must each conductor extend from an enclosure that is less than 8 inches in any dimension?
• In what environment must electrical tools be rated?
• Spare or unused raceways shall be sealed with sealants ______ for use with the cable insulation, conductor, insulation, bare conductor, shield, or other components.
• Which wiring method requires the least attention to fire safety in air-handling spaces?
• Cables or raceways installed using directional boring equipment shall be ______ for this purpose.
• Which type of raceway is not permitted for use in a wet location?
• Cables and nonmetallic raceways installed parallel in framing members should be ______ the nearest edge of the member.
• What is the danger of improperly installed recessed lighting?
• Each direct-buried single conductor cable shall be located ______ in the trench to the other single conductor cables in the same parallel set of conductors, including equipment grounding conductors.
• According to NEC, what is the minimum height for receptacles in living spaces?
• Why is it necessary to follow manufacturer's installation instructions?
• Which material is classified as a nonferrous, nonmagnetic metal without hysteresis heating?
• Environmental air-handling spaces must comply with which standard?
• What is a critical factor when using metal raceways in electrical systems?
• What must be done when cables or nonmetallic raceways are installed underground?
• Rigid metal conduit that is directly buried outdoors shall have at least how many inches of cover?
• What type of conductors must be kept within the same raceway?
• What is the primary concern when using ferrous metal raceways near corrosive conditions?
• Can direct-buried conductors or cables be spliced or tapped without the use of splice boxes?
• What is the main purpose of wiring methods in plenum spaces?
• Holes bored for cables in wood members must have edges that are ________ the nearest edge of the wood member.
• What is the purpose of a Ground Fault Circuit Interrupter (GFCI)?
• Which article in the NEC outlines the requirements for the installation of cables and conductors?
• What does the NEC state about the splices, joints, and terminations of conductors?
• Is a box or conduit body required when cables exit a conduit used for cable support or physical damage protection?
• What type of fittings should be used in raceways for accommodating movement caused by temperature changes?
• What should be used to protect NM cables passing through metal edges?
• The interior of underground raceways is classified as which location?
• What is the significance of the NEC’s "general requirements" section?
• What is required for protecting cables laid in wood notches against penetration?
• What is the minimum cover requirement for direct burial Type UF cable installed outdoors to supply a 120V, 30A circuit?
• What is the purpose of using conduit in electrical installations?
• Which type of conduit is commonly used in air-handling spaces?
• What must electrical equipment and wiring be installed in accordance with?
• Metal raceways, cable armor, and other metal enclosures shall be _______ joined together into a continuous electric conductor to provide effective electrical continuity.
• At what height above finished grade shall direct-buried conductors and cables be protected?
• What is the minimum size for a grounding electrode conductor for a 100-amp service according to the NEC?
• When installed under metal-corrugated sheet roof decking, are cables, raceways, and enclosures allowed in concealed locations as long as they are at least 2 inches away from a structural support member?
• When installing Type UF cable under a driveway, what is the minimum cover depth required?
• Raceways and cables installed into the ______ of open bottom equipment shall not be required to be mechanically secured to the equipment.
• In electrical raceway installations, what is the focus when positioning conductors?
• Wiring methods permitted in ceiling areas used for environmental air include ______.
• How should conductors be placed in metal raceways to minimize induction effects?
• What does Article 250 of the NEC address?
• When installing PVC conduit underground without concrete cover, what is the minimum required cover?
• When the opening to an outlet, junction, or switch point is less than 8 inches in any dimension, how far should each conductor extend outside the enclosure?
• Areas where acids and alkali chemicals are handled may present corrosive conditions, particularly when wet or damp. This statement is ______.
• A cable, raceway, or box installed under metal-corrugated sheet roof decking shall be supported so the top of the cable, raceway, or box is not less than how many inches from the lowest surface of the roof decking?
• In what locations is it prohibited to install receptacles?
• Which of the following options is a limitation for wiring in a plenum space?
• Direct-buried conductors, cables, or raceways, which are subject to movement by settlement or frost, shall be arranged to prevent damage to the ______ or to equipment connected to the raceways.
• Which statement is true regarding the use of fittings and connectors?
• What type of conductor is typically used for residential wiring?
• Which of the following metal parts shall be protected from corrosion?
• When nonmetallic wiring methods are exposed to chemical agents, they must be resistant based on what?
• A ______, with an integral bushed opening shall be used at the end of a conduit or other raceway that terminates underground where the conductors or cables emerge as a direct burial wiring method.
• What is the minimum allowable number of branch circuits for a residential dwelling?
• All conductors of the same circuit shall be ______, unless otherwise specifically permitted in the Code.
• Where independent support wires of a suspended ceiling assembly are present, they shall be secured at the ______ end(s).
• What are the requirements for securing and supporting conductors according to NEC?
• How often must a receptacle outlet be located in a dwelling unit according to NEC requirements?
• What factor must be considered while selecting conductors for an installation?
• What precaution should be taken when installing receptacles in bathrooms?
• All conductors of the same circuit, including grounded and bonding conductors, shall be contained within the same ________, unless permitted otherwise.
• What is the requirement for outdoor wiring regarding protection against moisture?
• Are flexible cords considered permanent wiring according to the NEC?
• What action should be taken for conduits or raceways through which moisture may contact live parts?
• Under what condition is equipment and devices permitted in ducts or plenum chambers?
• How should wiring be installed in a ceiling space?
• The use of plenum-rated cables is crucial for what main reason?
• Which kind of cover depth is required for low voltage lighting systems specified in different installation guidelines?
• In residential wiring, what is commonly the standard voltage used?
• Electrical wiring within a fire-rated floor-ceiling or roof-ceiling assembly shall not be supported by the ceiling assembly or ceiling support wires. Is this statement true or false?
• Which type of location classification do underground service conductors fall under according to the installation requirements?
• What type of cable is specifically designed for underground use?
• When can bushings replace boxes or terminals at raceway exits?
• Conductors of ac and dc circuits rated 1,000V or less may occupy the same ______ if insulation ratings match.
• What is the requirement for junction boxes that are installed in walls?
• What type of MC Cable is permitted to be installed underground under a building without a raceway?
• What is the primary purpose of requiring separate circuits for lighting?
• How high must a warning ribbon be placed above the ungrounded installation for direct-buried conductors that are buried 18 inches or more below grade?
• How should metal raceways be treated to ensure safety during installation?
• Insulated circuit conductors of which gauge and larger require protection from abrasion in raceways?
• In multiwire branch circuits, what conductor's continuity shall not depend on the device connections?
• The interior of raceways installed in wet locations above grade shall be considered a ______ location.
• What must electrical installations in potential fire spread areas aim to avoid?
• Which type of locations require GFCI protection?
• Conductors in raceways shall be _______ between outlets, boxes, devices, and so forth.
• Under what conditions can Type AC cable be used?
• Which fitting is required for raceways crossing structural joints to accommodate thermal expansion?
• According to NEC tables, how many conductors are allowed in a raceway without derating?
• Which type of circuit requires the use of GFCI protection?
• Which of the following statements is true regarding raceways and moisture control?
• Type UF cable used with a 24V landscape lighting system can have a minimum cover of how many inches?
• Fittings and connectors must be used only with which of the following?
• What does the term "load calculation" involve in electrical design?
• How should electrical tools and equipment be rated?
• How should raceways be configured before the installation of conductors?
• Raceways or cable trays containing electric conductors must not contain any pipe for other services besides ______.